Chimney Top — Caps, Covers & Draft · Anchor Component

Copper Chase Cover (Custom-Fabricated)

A chase cover is not a decorative lid — it is the water barrier over a framed chase, and the code-relevant failure is what happens when it ponds. We fabricate in solid copper with a full slope and standing seams so there is no flat area to hold water and no exposed fastener penetrating the drainage plane. Copper carries no coating to fail, which is the whole argument for it. The honest limitation: copper is a finish decision as much as a performance one, and if you dislike a green patina you will not like this cover in five years.

Specification

What the listing decides

Material: Solid copper
Store fit: Quote-to-fabricate, measured on site

How this part is bought

The part follows the finding

No part in this store is a loose transaction. This one links back to the graded inspection that surfaces the need, and across to the install service it belongs to — both performed by the same trained crew.

Upstream

Chimney Inspection

The graded inspection that documents the need for this part before it ships.

Start here

Installed by

Trained Install

The install service this component attaches to, fitted to its listing by the same crew.

See the work

Every store quote includes

A fit check — flue size, alloy, venting, and clearances verified against your inspection
Written installed pricing before anything is ordered
Installation to the component's listing by trained technicians
Documentation that closes the finding — so the warranty, your insurer, and the next inspector all see a job done right

Chimney Top — Caps, Covers & Draft

Request a quote

No price is listed — that’s the standard, not a sticker. Installed pricing depends on your flue, alloy, venting, and access, and we confirm it in writing after a fit check. No payment is taken online.

Specify your custom cap

Built to your figures by our fabricator. Spec it here; every measurement is verified on the fit check before a single cut.

Cap style

Size variant

Material

Gauge

Outside measurements

Whole inches plus the fraction, for each side: A (top), B (right), C (bottom), D (left).

A — Topin

B — Rightin

C — Bottomin

D — Leftin

Add 1/2" of clearance to each of the A, B, C and D outside measurements before you submit — Plano fabricates to these exact figures, so the extra half-inch is what lets the finished cap seat over the masonry. I've added the 1/2" clearance to A, B, C and D.

Flue holes

Inside-hole measurements run from the outside edge to the edge of each hole, numbered from the top, then from the left — one pair per flue.

Number of flues

Hole 1

Skirt height

Leg height

Add-ons — available, priced on quote

Rush — faster turnaroundAvailable — priced on quote. (Plano's rush is a 2-business-day fabrication; we confirm the upcharge in writing, never a sticker price online.)Lifetime warrantyAvailable — priced on quote. Plano backs the fabrication for life; we confirm the cost in writing with the rest of the installed quote.

Every figure rides into the quote as your stated spec — confirmed on the measured fit check before fabrication. No price is taken online.

Include professional installationFitted to its listing by the trained crew as Trained install. Leave it on — most parts here are a safety system, not a box you fit on a Saturday.

Pick a preferred window next — we confirm it by phone

(469) 838-6843

Keep browsing

More from the Chimney aisle

Architectural Multi-Flue Shroud (Decorative)

A shroud is an appearance product and we will not pretend otherwise. What matters from a standards view is that it does not become an obstruction: a shroud sized or seated wrong restricts the flue outlet and changes draft, which is the difference between decoration and a defect. We size the opening area against the flues underneath and set it clear of the crown. If your inspection did not flag a draft problem, a shroud will not create one — and it will not fix one either.

View pageQuote

Integrated Crown-Cap Unit (Drip-Edge Crown + Cap)

A cracked crown fails because water gets into the masonry through it. This is the assembly that removes the crown from the water path entirely: a single stainless top that caps every flue and overhangs far enough to throw runoff clear of the brick rather than down it. Where a crown rebuild restores the original detail, this supersedes it. The trade-off is visual — it reads as metal, not masonry, and on a historically detailed chimney that is a real objection.

View pageQuote

Powered Draft System (Enervex / Exhausto Inducer + Modulating Control)

Mechanical draft is a legitimate engineered solution and it is also the point at which we have stopped fixing the chimney and started overriding it. A roof inducer with a modulating control will hold draft on a flue that cannot produce it naturally — an undersized flue, a stack shortened by a later addition, a house too tight to supply combustion air. We specify it only after the inspection has ruled out the correctable causes, because a fan on a defective flue is a powered defect.

View pageQuote

Everything in Chimney Top — Caps, Covers & Draft

15+

Years in the field

NFPA 211

Checklist

48h

Written report

< 2hr

Response

Ready when you are

Get it inspected. Get it in writing.

Flat fee confirmed when you book. Same-week scheduling. A pass/fail verdict within 48 hours.

Book an Inspection (469) 838-6843

Licensed & Insured Same-Week Scheduling Photo-Documented Findings

Emergency

24/7 Response

Chimney fire, storm hit, active leak, or a flue you're not sure about? We answer 7 AM to midnight and the assessment ends in a written safe-to-use verdict — including a do-not-use notice when the evidence supports one. After-hours dispatch runs subject to crew availability.

Emergency line